Menu

Tube Carbone ICS White Out BEMAN ARCHERY

Manufacturer: Beman

Condition: New

Availability:

Beman WHITE OUT is the next evolution of graphics on a hunting arrow. Designed with grayed out Realtree camo for high visibility and big game blood traceability. Shoot Beman WHITE OUT and see what you've been hitting.

8,99 €

No reward points for this product.


More info

Accessories

Comments

Beman WHITE OUT is the next evolution of graphics on a hunting arrow. Designed with grayed out Realtree camo for high visibility and big game blood traceability. Shoot Beman WHITE OUT and see what you've been hitting.

  • Straightness: +/-.003
  • Direct-fit S Nock - installed
  • CB Inserts - included
Arrow Size300340400500
Weight (GRAINS/INCH)9.68.88.17.5
RPS Point (INCH)9/329/329/329/32

SHAFT PREPARATION

Cut shafts to length using only a high-speed abrasive wheel cut-off tool designated for arrow shafts. Never use rotary tube cutters, a hacksaw or methods that can damage the shaft and leave a rough cut. Lightly chamfer the inside of the shaft, just enough to remove any burrs. Thoroughly clean the inside of the shaft with a cotton swab wetted with 91% to 99% isopropyl alcohol (not rubbing alcohol, which can contain oil). CAUTION:Always wear a NIOSH approved dust mask and safety glasses when cutting any arrow shafts. Be sure to use a dust collector to vacuum up all of the dust when cutting arrow shafts.

FOR C2 CARBON SHAFTS

Easton or AAE brand epoxy or 3M DP390 24-hour cure flexible two-part epoxies are recommended. Apply a small ring of adhesive, just inside the end of the shaft and a generous coating on the entire shank of the point or insert. Slowly twist the point or insert into shaft and seat it against end of shaft. Wipe off any excess adhesive with a cloth or paper towel. Stand the shaft vertically on the point or insert to cure. Be sure epoxy does notflow into insert threads. This is a permanent installation, and inserts cannot be removed without damaging the shaft.

CARBON SHAFTS UNI BUSHING INSTALLATION

AAE Fastset or other gel-type cyanoacrylate cements are recommended. Apply a thin ring of adhesive completely around the inside diameter of the shaft within 1⁄16” from the open end. Insert UNI Bushing and quickly seat completely against end of shaft. Stand shaft with UNI Bushing upright.

HIT INSERT COMPONENTS

See shaft preparation and assembly instructions packaged with HIT equipped models. Use Easton brand HIT 24-hour epoxy.



No customer comments for the moment.

Write your review

Related products
  • Lot Tube Hunting CenterShot Carbone Beman
  • Carbon Tube Aftermath Easton
  • Tube Carbone Bloodline Camo EASTON
  • Tube easton Carbone Bow Fire
  • Carbon tube ICS HUNTER Realtree BEMAN
  • Tube Carbon Beman ICS Hunter Patriot
  • Shaft Carbon Predator 2 CARBON EXPRESS
  • Tube ST Excel Carbon de chez Easton
  • 5MM Axis Carbon tube with EASTON ARCHERY insert
  • Tube Axis traditionel Carbone Easton
  • Tube Carbone IRONWOOD de chez WIN&WIN
  • Lot de 12 Tubes Carbone GOLD TIP HUNTER TRADITION
  • Tube Carbon POWERFLIGHT EASTON
  • Shafts Carbon Pants Traditional Bamboo BEARPAW
  • Shaft Carbon Penthalon Hunter Extreme BEARPAW
  • Shaft Carbon Black HELLCAT Win & Win
  • Tube Pentathlon Byron Ferguson Heavy Hunter BEARPAW
  • Carbon Tube Pants Slim Line Timber Bearpaw
  • Tube Carbon Pentathlon Traditional Timber BEARPAW
  • WIND Tube Light Carbon WIN & WIN Archery
  • Carbon Shaft METEOR WIN WIN BLACK
  • Carbon Tube Maxima Red CARBON EXPRESS
  • Carbon Tube Maxima Hunter CARBON EXPRESS
  • Carbon Tube Edge MAXIMAL 3D and Hunting
  • Carbon Tube PileDriver Hunter 3D CARBON EXPRESS
  • Penthalon Traditional Extreme Carbon Tube BEARPAW
  • Carbon One Tube 600 EASTON ARCHERY
  • Carbon Tube 33" BACKBONE 5.2" MAXIMAL ARCHERY
  • HERITAGE tube imitation wood CARBON EXPRESS
  • Carbon tube TIMBER 6.2 BUCK TRAIL ARCHERY TRADITION